2024-07-25 14:34:50 +08:00
|
|
|
|
1、功能说明
|
|
|
|
|
|
1.LPTIM定时产生EXTI20中断，唤醒CPU进行IO翻转
|
|
|
|
|
|
2、使用环境
|
|
|
|
|
|
软件开发环境：KEIL MDK-ARM V5.34.0.0
|
|
|
|
|
|
IAR EWARM V8.50.1
|
|
|
|
|
|
硬件环境：基于N32G430C8L7-STB V1.0开发
|
|
|
|
|
|
3、使用说明
|
|
|
|
|
|
系统配置;
|
|
|
|
|
|
1.时钟源：
|
|
|
|
|
|
HSE = 8M, PLL = 128M, AHB = 128M, APB1 = 32M, APB2 = 64M, LPTIM CLK = LSI 40K
|
|
|
|
|
|
2.中断：
|
|
|
|
|
|
LPTIM周期触发EXTI20中断，唤醒CPU
|
|
|
|
|
|
3.端口配置：
|
|
|
|
|
|
PB7被选为IO输出
|
|
|
|
|
|
4. LPTIM：
|
|
|
|
|
|
LPTIM连续计时模式
|
|
|
|
|
|
指示：
|
|
|
|
|
|
1.编译后开启debug模式，可以观察到PA1脚有一个周期翻转，CPU继续进入低功耗模式
|
|
|
|
|
|
4、注意事项
|
|
|
|
|
|
无
|
2024-07-25 14:33:47 +08:00
|
|
|
|
|
2024-07-25 14:34:50 +08:00
|
|
|
|
|
|
|
|
|
|
1. Function description
|
|
|
|
|
|
1. LPTIM generates EXTI20 interrupt regularly, wakes up the CPU for IO flipping
|
|
|
|
|
|
2. Use environment
|
|
|
|
|
|
Software development environment: KEIL MDK-ARM V5.34.0.0
|
|
|
|
|
|
Hardware environment: Developed based on the evaluation board N32G430C8L7-STB V1.0
|
|
|
|
|
|
3. Instructions for use
|
|
|
|
|
|
System Configuration;
|
|
|
|
|
|
1. Clock source:
|
|
|
|
|
|
HSE = 8M, PLL = 128M, AHB = 128M, APB1 = 32M, APB2 = 64M, LPTIM CLK = LSI 40K
|
|
|
|
|
|
2. Interrupt:
|
|
|
|
|
|
LPTIM cycle triggers EXTI20 interrupt, wakes up CPU
|
|
|
|
|
|
3. Port configuration:
|
|
|
|
|
|
PB7 is selected as IO output
|
|
|
|
|
|
4. LPTIM:
|
|
|
|
|
|
LPTIM Continuous Timing Mode
|
|
|
|
|
|
Instructions:
|
|
|
|
|
|
1. Turn on the debug mode after compiling, and it can be observed that the PA1 pin has a cycle flip, and the CPU continues to enter the low-power mode
|
|
|
|
|
|
4. Matters needing attention
|
|
|
|
|
|
none
|
